The FShaderCache provides mechanisms for reducing shader hitching in-game.

Choose your operating system:





The FShaderCache provides mechanisms for reducing shader hitching in-game. It supports the OpenGLDrv and MetalRHI RHIs, and works on Mac, Linux, and Windows platforms.

There are a number of console commands that can be used to enable or disable FShaderCache functionality.

Console Command


r.UseShaderCaching [0/1]

  • Early submission during shader deserialisation rather than on-demand.

  • Tracking of bound-shader-states so that they may be pre-bound during early submission.

r.UseShaderDrawLog [0/1]

Tracking of RHI draw states so that each bound-shader-state can be predrawn.

r.UseShaderPredraw [0/1]

Predrawing of tracked RHI draw states to eliminate first-use hitches.

r.PredrawBatchTime [Time in (ms)]

Control over time spent predrawing each frame to distribute over many frames if required. Use -1 for all.

r.UseShaderBinaryCache 0/1

Accumulation of all shader byte code into a single cache file

r.UseAsyncShaderPrecompilation 0/1

Asynchronous precompilation of shader code during gameplay

r.TargetPrecompileFrameTime [Time in (ms)]

The target maximum frame time to maintain when r.UseAsyncShaderPrecompilation is enabled. Use -1 to precompile all shaders at once.

r.AccelPredrawBatchTime [Time in (ms)]

An option to temporarily accelerate predrawing when in a non-interactive mode such as a load screen. Use 0 to use r.PredrawBatchTime.

r.AccelTargetPrecompileFrameTime [Time in (ms)]

An option to accelerate asynchronous precompilation when in a non-interactive mode such as a load screen. Use 0 to use r.TargetPrecompileFrameTime.

r.InitialShaderLoadTime [Time in (ms)]

A maximum amount of time to spend loading the shaders at launch before moving on to asynchronous precompilation. Use -1 to load synchronously)


The cache should be populated by enabling r.UseShaderCaching and r.UseShaderDrawLog on a development machine. Users/players should then consume the cache by enabling r.UseShaderCaching and r.UseShaderPredraw. Draw logging (r.UseShaderDrawLog) adds noticeable fixed overhead so avoid enabling it in shipped products if possible. The binary shader cache can either be accumulated during play through or (currently Mac targets only) during cooking by specifying the shader platforms to cache in the CachedShaderFormats array within the /Script/MacTargetPlatform.MacTargetSettings settings group of Engine.ini. For OpenGL the binary cache contains enough data about shader pipelines to construct fully linked GL programs or GL program pipelines (depending on availability of GL_ARB_separate_shader_objects) but not enough for pipeline construction on any other RHI. This can help reduce the amount of hitching on OpenGL without first playing through the game, though this is still advisable for maximum effect. Since the caching is done via shader hashes, it is also advisable to only use this as a final optimization tool when content is largely complete as changes to shader hashes will result in unused entries accumulating in the cache, increasing cache size without reducing hitches.

The code will first try and load the writable cache, then fall back to the distribution cache if needed.

Cache Type

Cache Location


<Game>/Saved/DrawCache.ushadercache, <Game>/Saved/ByteCodeCache.ushadercode


<Game>/Content/DrawCache.ushadercache, <Game>/Content/ByteCodeCache.ushadercode

Integration Steps

While there are a number of console commands you can use to reduce hitching in your project, there is a recommended priority order to enable options to maximize performance while avoiding additional project work.

  1. Enable r.UseShaderCaching & r.UseShaderPredraw in the project configuration for all users.

  2. If possible, enable r.UseShaderDrawLog only for internal builds & ensure that shader draw states are recorded during final QA for each release. When not feasible (e.g. an extremely large and/or streaming game), enable for all users.

Test whether this setup is sufficient to reduce hitching to an acceptable level, as the additional optimizations require more work and have significant side effects.

  1. If the above is insufficient, then also enable r.UseShaderBinaryCache and configure the CachedShaderFormats to ensure population of the binary cache (currently Mac only).

  2. All shader code will now be loaded at startup and all predraw operations will occur on the first frame, so if the loading times are too extreme also set r.PredrawBatchTime to a value greater than 0 in ms to spend predrawing each frame.

  3. You may also wish to specify a larger value for r.AccelPredrawBatchTime that can be applied when showing loading screens or other non-interactive content.

  4. To inform the shader cache that it may accelerate predrawing at the expense of game frame rate, call FShaderCache::BeginAcceleratedBatching, and when it is necessary to return to the less expensive predraw batching, call FShaderCache::EndAcceleratedBatching.

  5. A call to FShaderCache::FlushOutstandingBatches will cause all remaining shaders to be processed in the next frame.

  6. If the project still takes too long to load initially, then enable r.UseAsyncShaderPrecompilation and set r.InitialShaderLoadTime to a value > 0. As the initial shader load time increases, the work that must be done while the game is running decreases.

  7. You can tweak the desired target frame time while asynchronously precompiling shaders by modifying the value of r.TargetPrecompileFrameTime.

  8. As with predraw batching, a more aggressive value can be specified for precompilation by setting r.AccelTargetPrecompileFrameTime to a larger value and then calling FShaderCache::BeginAcceleratedBatching (and FShaderCache::EndAcceleratedBatching afterwards).

  9. With r.UseAsyncShaderPrecompilation enabled, a call to FShaderCache::FlushOutstandingBatches will also flush any outstanding compilation requests.

Handling Updates/Invalidation

When the cache needs to be updated and writable caches invalidated the game should specify a new GameVersion. Call FShaderCache::SetGameVersion before initializing the RHI (which initializes the cache). This will cause the contents of a cache generated by a previous version to be ignored. At present you cannot carry over cache entries from a previous version.

Region/Stream Batching

For streaming games, or where the cache becomes very large, calls to FShaderCache::SetStreamingKey should be added with unique values for the currently relevant game regions/streaming levels (as required). Logged draw states will be linked to the active streaming key. This limits predrawing to only those draw states required by the active streaming key on subsequent runs.

Help shape the future of Unreal Engine documentation! Tell us how we're doing so we can serve you better.
Take our survey