Smooth Frame Rate

Overview of the Smooth Frame Rate option inside the Engine Settings.



The Smooth Frame Rate option (found in the Project Settings under General Settings/Framerate) is enabled by default and can be used to define the min/max acceptable frame rates on a per-application basis. To better understand how Smooth Frame Rate works, an understanding of Vertical Sync (or VSync) is also needed as the two have a lot in common. 

Vertical Sync

VSync essentially is a way to control screen tearing (when the Frame Rate exceeds the Refresh Rate of the monitor) or stutter (when the Frame Rate drops below the Frame Rate Cap, typically 60 FPS) in your rendered application. The functionally works by setting an overall Frame Rate based on the video card demands and the Monitor refresh rate; this will yield a very harsh jump sometimes between 30 FPS and 60 FPS on modern machines which yield the stuttering effect.

With modern monitors and video cards, VSync is not often as critical an issue (depending of course on the demands of the system and desired results), and for that reason, VSync for most is set to Application Specific in your Video Card's Configuration Manager (for example, the NVIDIA Control Panel). This enables each application to decide whether you want to use VSync with it or not. The image below is an example that illustrates what happens when the Frame Rate drops which produces VSync stuttering. 


Most modern video cards have adaptive VSyncing which yields better results with less stuttering.


Adaptive VSync prevents screen tearing and reduces stuttering by locking the higher-end of Frame Rate to 60 FPS and turns VSync off below 60. 

Both images above were used in NVIDIA's Adaptive VSync documentation page.

Smoothed Frame Rate Range

With Frame Rate Smoothing, the application is determining what range is acceptable for Frame Rate wandering, so you can cap your Frame Rate between Min and Max allowable values. Since this is application based, it will make these changes before any VSync changes. 

As an example, if you have an application that runs amazingly well on a Titan X card at around a consistent 75 to 85 FPS, most users will not have the higher-end machine to achieve this (or if you were developing for a console, the target is usually 60 FPS). You can set the Smooth Frame Rate to a range of 40 to 60 FPS. 

By doing so, this means that even though your higher-end machines could run at a higher Frame Rate, for the best experience for all, you cap the Frame Rate at 60 FPS. Taking this a step further, if you have a user who is on a lower-end machine which is struggling at 40 FPS, the VSync hardware changes will probably limit the FPS of the application to 30 FPS after the Smooth Frame Rate shifts to a lower 40 FPS. 

You can define this inside the Project Settings under General Settings/Framerate with the Smoothed Frame Rate Range: **


You can also set whether the Min/Max ranges are: Exclusive (excludes value), Inclusive (includes value), or Open (value is not capped).

Select Skin
언리얼 엔진 문서의 미래를 함께 만들어주세요! 더 나은 서비스를 제공할 수 있도록 문서 사용에 대한 피드백을 주세요.
설문조사에 참여해 주세요

새로운 언리얼 엔진 4 문서 사이트에 오신 것을 환영합니다!

문서 사이트에 대한 의견을 모을 수 있는 피드백 시스템을 포함해서 여러가지 새로운 기능을 준비하고 있습니다. 아래 Documentation Feedback 포럼(영문) 또는 언리얼 엔진 네이버 공식 카페(한글) 중 편하신 곳에 의견이나 문제점을 알려 주세요.

새 시스템이 준비되면 알려 드리겠습니다.

네이버 카페
공식 포럼