Language:
Page Info
Skill Level:
Engine Version:

Computing Lightmap UV Coordinates

Choose your OS:

In order to use static lighting (Lightmass) in UE4, you must compute a set of unwrapped UV coordinates for the model. This UV mapping is referred to as the lightmap for the model. Getting a good lightmap is one part science and one part art. The following steps detail how to go about computing lightmap UV mapping in SpeedTree.

Model lightmap and density on the left; Lightmapped model in UE4 on the right.

Step 1: Switch to Lightmap Density Rendering Mode

Using the Render toolbar button, switch the rendering mode to Lightmap Density. Your display should look like the one in the image below.

ue4_starting_lightmap.jpg

This visualization shows how well your lightmap resolution is distributed across your model and is intended to closely match the same visualization mode in UE4 (Show -> Lightmap density). Green sections of the model represent ideal density. Blue indicates that the lightmap resolution is too low and may show artifacts when the lightmap is built in UE4. Red indicates the lightmap resolution is too high and is being wasted on that geometry.

The lightmap itself is rendered in the lower left hand corner. Select part of the model to see where it is represented in the lightmap. You can also select triangles in the lightmap to see which part of the model they come from. You want to use as much of the lightmap as possible, with big sections of the model getting big sections of the lightmap. More on how to achieve that later.

The units of the model matter in the visualization. Select the Tree generator and edit Lightmap:Scale to scale the model by the same amount you will in UE4 when you import it. The default value here matches the default value of the importer.

You can change how large the lightmap is rendered in the viewport by editing the corresponding property in the Window properties.

Step 2: Pick a Lightmap Resolution

The resolution of the lightmap is dependent on your project's requirements and the complexity of the tree. The goal is to use the lowest possible lightmap resolution that gives you adequate coverage given the model's placement in your scene.

Set the target lightmap resolution by selecting the Tree generator and editing the Lightmap:Resolution property. It may be possible that the model is too complex to fit in the resolution you have chosen. If so, you will get a warning in the output window and the resolution will be bumped to the smallest resolution that will give each node in the model at least one texel in the lightmap while maintaining the one texel border necessary to prevent rendering artifacts.

Step 3: Tune the Lightmap

Once you have picked a resolution, the next step is to tune how the lightmap is distributed across the model to make sure the parts of the model that need the most density have it. In general, you will want the most density in the trunk, low branches, and roots. This is the area most often seen by the player and the most prone to obvious artifacts if the density is too low. Leaves often have to have comparitively low density to fit the model in a reasonably small lightmap.

Use a combination of the following tools to tune the lightmap density distribution:

  • Reset - Select Tools -> Reset lightmap to set all lightmap scalars to 1.0 except the leaves. They are set to 0.0 so that each leaf gets exactly one texel and no more to start with (we will up that later).

  • Material Scales - Each material has a property called Unwrap scale. Increase or decrease this value to change the relative size of each piece of geometry that uses this material (very useful for caps).

  • Generator/Node Scales - Each generator/node combination that can house geometry has a Lightmap:Scale property. Change this value to change the size of the selected object's space in the lightmap. The distribution curve on branches can be used to shift the distribution of lightmap space on the object itself (without changing the actual lightmap area used). This curve is used to counteract the fact that branch lightmap density naturally increases near the tip as the geometry narrows but uses the same texture space.

  • Lightmap Resolution - If you just cannot make it work well in the resolution you have selected, you may need to bump it up by selecting a higher resolution like you did in Step 2. The layout will drastically change so you may need to do a reset and start over if it comes to this.

You can go into node editing mode and scale up individual branches, fronds, and leaves to tackle particularly troublesome areas.

Best Practice: Keep the leaves at zero until the branches are good. Then scale up the leaves to fill in all of the empty space.

Our algorithm aggressively tries to fit everything in the resolution you have selected. If you scale one component up so large that not everything will fit, the algorithm will adjust and change sizes to make it fit. If this happens, you may suddenly lose density where it was fine before. This effect can be counteracted by lowering the scale you just edited to get it back in range.

Step 4: Pick the Lightmap Resolution in Unreal Engine 4

When you import the model in UE4, it will have a default lightmap resolution of 64 like all Static Meshes. Select the mesh asset and enter the ligthmap resolution (Details -> Static Mesh Settings -> Lightmap Resolution) you used here. When you build lighting in UE4, you should have amazing results on some of the hardest types of geometry to lightmap!